Question

1 Rating

Tagged in

Engineering

Mechanical Engineering

Find answers to questions asked by students like you.

Q: Which of the following is not a Gen2 plasma ignition system? O Dual frequency drive O Capacitive Mag...

A: ignition system: The ignition system create an electric spark in the engine combustion chamber, whi...

Q: For the following mechanism with Rag = 4 ft, RpA = 6 ft, and p = 0.75 ft (radius of the Roller 4), a...

A: Data given- RAB = 4ft RPA = 6ft Radius of roller = 0.75 ft V2 = -15i ft/s <OAB = 45° So the dime...

Q: Engineering drawing

A: Click to see the answer

Q: 1. The 12 kN m torque is applied to the free end of the 6-m steel shaft. The angle of rotation of th...

A: you have posted multiple questions. As per the guidelines I am able to answer one question only. So ...

Q: QUESTION 1 The Mach number behind a normal shock wave is 0.4752. What is the Mach number infron...

A: Given data as per the question Mach number behind a normal shock wave = 0.4752 mach no. behind the w...

Q: The quality of water is 50% at 500 psia. Calculate the specific volume.

A: 1psia=6894.75Pa 500 psia = 3.44 Mpa Quality =50%=0.5 From the steam table At 3.44 Mpa vf=0.001233 v...

Q: The 3 hinged parabolic arch shown below, has a span of 160m. The two supports are hinged and third h...

A: Data given - L = 160 m RB = 95.25 kN HB = 336 kN

Q: Specifications require that a concrete mix contain 280 kg/m3 and have a water-to-cement ratio of 0.5...

A: Click to see the answer

Q: solve the question given in the image.

A: Given, d = Diameter of the circle = 200 mm σx= Normal stress in horizontal direction = 160 MPa σy= ...

Q: Consider the given mechanisms/machines/equipment and provide thefollowing requirements for these mec...

A: Link is an moving part of the machine. it must be resistant Kinematic chain is the no of links are c...

Q: A sphere is fired downwards into a medium with an initial speed of 34 m/s. If it experiences a decel...

A: Data given- Intital speed of the sphere = 34 m/s Declaration = -7t m/s2 Need to determine s = ?

Q: State the advantages and disadvantages of natural diamond bits?

A: Click to see the answer

Q: There is 3.5 L saturated liquid water at 175 kPa pressure in the frictionless moving piston-cylinder...

A: Given that the frictionless piston cylinder system contains saturated liquid water. Volume, V=35L=3....

Q: Determine the moments of Q about (a) point 0; and (b) point C. The magnitude of Q is 100 N.

A: GIVEN: The magnitude of Q =100 N TO FIND: The moment of Q about (a) point O (b) point C

Q: what the Procedure of this experiment ? Experiment Title: Performance of a Centrifugal Pump.

A: Centrifugal pump is the type of hydraulic machine it uses centrifugal force to convert mechanical en...

Q: The concrete dam in the shape of a quarter circle. Determine the magnitude, location and the directi...

A: Let the Fv is the vertical component and Fh is the horizontal component Fv=ρgAABCbFv=1000(9.81)4(4)-...

Q: Question 2. Differentiate between the following: a) Kinetics and Kinematics b) Particle and Rigid bo...

A: Click to see the answer

Q: The rim of a flywheel has the cross section A-A shown. Determine the volume and mass of material nee...

A: Click to see the answer

Q: Figure M02 shows a plate subject to loads. Replace the loads by an equivalent force through C and a ...

A: (b) For Vertical couple; Here tanθ=75100θ=36.87°tanα=7550α=56.31°

Q: Please find the attached image of the Question

A: Belt Drive is a power transmission device It is also used to carry material from one place to anothe...

Q: The wind blows uniformly on the front surface of the metal building with a pressure of 1.8 kN/m?. De...

A: Given Data: The wind pressure is P = 1.8 kN/m2. The front view of the building can be dawn as belo...

Q: For the system shown in Figure 2, the input is applied torque, the output is angular acceleration of...

A: Click to see the answer

Q: a) Determine the normal strain across the AC and BCb)Determine average shear strains on all corners.

A: Given:Rectangular section Dimension : width=500 mmheight= 300 mm

Q: If your Household Refrigerator malfunctions in cooling, what could be the reasons for which cooling ...

A: There are times when the refrigerator doesn't cool enough or no cooling at all which makes it unplea...

Q: In a welding process, a current of 400 A flows through the arc when the voltage is 35 V. The length ...

A: Click to see the answer

Q: Using the method of joints, please determine the forces in DC, DE, CB, CF and EF.

A: Click to see the answer

Q: A solid right circular cone has SG = 0.99 and floats vertically as in Fig. P2.147. Is this a stable ...

A: Let r be the radius of the surface ∑Fz=0γwπ3(R2h-r2z)-0.99γwπ3R2hwith zh=rRzh=(0.01)1/3=0.2154

Q: 3: Calculate the forces in members CD, HI, and CJ of the truss shown below. Clearly indicate if each...

A: Click to see the answer

Q: A leaking triangular trough, 5 ft across, 9 ft in length and with a depth of 6 ft, is continually fi...

A: Given: L= 9 ft Rate of filling = 17 ft3/min Rate of leaking = 0.25 ft3/min The triangular notch is g...

Q: The state of stress at a point in a loaded solid is given as [5 0 2 [0]=|0 0 0 MPa [2 0 -5 (a) Calcu...

A: The normal stress in x-direction, σxx= 5 MPa The normal stress in z-direction, σzz = -5 MPa The shea...

Q: three kg of saturated water at 125 kPa is completely vaporized. Calculate the volume

A: Use steam table To find out the specific volume at 125KPa Use Interpolation Method 120.82-125120.8...

Q: Drilled hole’s Ø made by twist drills are usually rough (surface finish) and often machined oversize...

A: The drills that are produced by the twist drills are usually rough. There will be a need for high ac...